This FAQ tries to answer some of the more common questions we get asked about the process for PCB design.
Q. What is the process of designing a printed circuit board?
To start with we need a schematic of the design, and a bill of materials of the components to be used in the design. Further some concept of the mechanical requirements and board size.
Using the BOM as reference, footprints of the components are taken from libraries or created from manufacturer datasheets. From the schematic a netlist with all the PCB connections is generated and loaded into the PCB layout software along with the footprints.
A mechanical profile and layer structure for the design is then determined and drawn in the PCB software.
Now a board placement is created where all the components are optimally placed to facilitate routing, mechanical requirements and any electrical requirements such as impedance, high speed routing etc.
Routing commences such that all design requirements such as impedance, current carrying, and crosstalk are met until the board is 100% connected up.
Lastly, a Design Rule Check is performed using the design software to check design rules and the connectivity of the schematic netlist is correctly implemented.
A final tidy of the routing, power planes and the silkscreen designators plus and further checks.
Once all is approved manufacturing files are generated and checked again to be sent of to the manufacturer.
Q How long does it take?
It depends on the board size and how much needs to be done.
When all available information is provided Align PCB Design can provide an accurate estimate of the number of hours for each stage of the design process and the total estimated time.
As far as pricing this can be handled in an up front quote or an hourly rate with an estimate of the expected hours to complete the design.
Q. Can you draw the schematic?
Simplest is being provided a fully drawn schematic in Altium. If the schematic has been drawn in a different CAD package translators can often be used to translate it. If there are no translators it may need to be redrawn.
Align PCB Design can also draw up the schematic from hand drawn sketches, cut and pasted drawings. Sometimes we have to re-draw a schematic if all that exists is a legacy printout.
Q. How is the Bill Of Material created?
Usually the client chooses the components and a preferred supplier. Align PCB Design can assist and perform this process if required using the most readily available suppliers.
Q. What do I need to provide to have a PCB layout created?
Align PCB Design gets provided everything from hand drawn schematic sketches all the way to Altium schematics and complete BOMS and mechanical outlines. We are able to work with whatever you can provide.
Q. Can I have a PCB cloned from an existing design?
An existing PCB can be manually copied depending in the complexity. For a single sided or doubled sided board the connections can all be seen and can be measured and drawn in Altium. For 4 layers or more it usually requires the board to be shaved down to remove the outer copper layers which is a slow and meticulous job.
Usually PCBs need to be depopulated so that all the copper tracking can be clearly seen. Sometimes boards can be copied with out depopulating if they aren’t overly complex.
With any reverse engineering like this, multiple iterations of checking that no connection has been missed is essential and time consuming.
Q. Can Align PCB Design reverse engineer an existing printed circuit board to derive the schematic?
This depends on complexity and is very time consuming. Usually this process is done for designs such as Military or Railways where boards are kept in service for decades and the original artwork gets lost.
This requires copying the board as in the previous question, but then slowly deriving all the connections between the components. It also requires knowing what all the component values are. If there is an existing Bill Of Material this is ideal, otherwise it requires desoldering and measuring discretes if they can’t be read. ICs can be straight forward if known manufacturers were used but often they can be marked with very generic labelling that makes determining the actual part difficult.
This process is therefore time consuming and prone to errors and some engineering to determine likely components. Creating a prototype is often a very necessary part of the process to iron out any issues.
Q. How many layers?
The simplest designs are on 2 layers or 4 layers which are also the most cost effective. 4 layer allows for having solid ground and power planes.
Boards can be increased to just about any number of layers. However this increases cost and obtaining required impedances gets much harder and keeping the board within a 1.6mm thickness are limiting factors. Therefore boards usually are a maximum of 10-12 layers.
Q. Fine Pitch BGAs and microvias
When BGAs get below 0.8mm pitch they are often defined as requiring microvias. As microvias increase manufacturing cost and limit the number of manufacturers who can make the board, sometimes it is possible to do the BGA breakout with conventional vias but does require greater effort and skill to complete this.
So Align PCB Design will design to keep this complexity down making the board more manufacturable and cost effective if required.
Q. Do you make printed circuit boards?
No. but I can recommend manufacturers that will suite the clients requirements.
Q. How do you define impedances?
Impedances are calculated for USB, Ethernet etc and then layed out in the board with those track and spacings for a proposed board build. Board layups sequences are designed to use the most common materials as possible such that can be handled by the majority of manufacturers.
The stack and impedance specifications are then either put in the mechanical drawing or just the gerber files.
What is the documentation package?
This package includes all generated files including the design files, BOM, 3D Step, drawings, gerbers, drill files, pick and place, DXF. All files that are required for the project are provided to the client.
Q. What needs to be provided to the manufacturer?
From the design file at minimum the gerber files of each layer must be generated, which includes silkscreen, soldermask and all the copper layers. There must be a file that defines the boards outline as well. An NC drill file to define the drilling locations and drill sizes. If it is a surface mount board gerber files showing the solder paste stencil pattern is also required.
If the board is to be assembled the package must also include a pick and place file to define component locations and rotations.
It is also wise to define the specifications for the boards manufacture including colour of silkscreen and solder resist, board thickness, material, copper thickness and layup sequence. Further any critical issues such as impedances.
Q. Can I import a file from another design package.
Altium has various importers of other packages such as KiKad, Eagle and Mentor packages. Not everything can be imported however. Upon importing there are usually some errors that need to be checked for and tidied up.
Q. I have the gerber files for a previous design can you edit them.
A. Editing actual gerber files is very difficult and prone to making mistakes. Gerber files can be loaded into Altium and edited more easily but there is no “intelligence” in the tracking so it can look like a PCB design file but doesn’t carry any of the embedded information that allows for BOMs or DRCs.
Q. I have gerbers, drill and a paper copy of a schematic, can this be made into a Altium PCB.
Gerbers can be imported but they have no embedded information such as components or nets. To do this a footprints need to be made from the file and then placed into the pcb file. This is quite a time consuming processes depending on how many different footprint packages there are. From this a full PCB file can be created.
The schematic can be redrawn, which is a slow process and requires a lot checking to make sure no errors are introduced. Alternatively a text file Netlist can be created from the schematic printout, which can be faster but is much less useful. Once schematic and PCB have been created they can be compared to guarantee no errors have been introduced.
Q. Do you design on a grid?
For through hole boards they may be designed on a regular 100mil imperial grid. As board technology increases and fine pitch metric SMD components get used, the concept of a grid gets blurred and might be as fine as 0.001mm and essentially become gridless. Grids can exist on the board such as for connectors on a regular 0.5mm, fiducials on a 1mm grid, and functional blocks having their own grid as required.